Leading 10 common forklift accidents ， forklift procedure need to pay attention to these issues ！.
Leading 10 common forklift accidents ， forklift procedure need to pay attention to these issues ！.
Blog Article
Don't undervalue the forklift at the office. If the procedure is bad, there will be major accidents in minutes, and there are numerous crashes entailing forklifts.
Case 1: The forklift cargo obstructed the vehicle driver's sight, and the individual in front can not be found, resulting in a moving accident.
Situation 2: In order to preserve the balance of the forklift when raising heavy items, the staff members utilized their body weight as the weight, which practically created casualties.
Instance 3: The width of the forklift cargo goes beyond the allowable width of the route and hangs on the roadside shelf, which almost creates an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Case 5: The forklift motorist did not see the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the personnel unlawfully, the forklift driver does not wear the safety belt, the forklift lifter falls and the vehicle driver is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not use a seat belt and fell from the automobile when it surrendered and was squashed.
Forklift procedure ought to pay attention to these issues ：.
Start.
1. Prior to starting, observe the surroundings, and after verifying that there are no challenges that prevent the safety of driving, beep the horn first and then start.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be safe before starting.
3. When the forklift starts with a tons, the motorist should initially confirm that the tons is steady and trusted.
4. The start has to be slow-moving and consistent.
Driving.
1. When driving, the elevation between the bottom end of the fork and the ground ought to be kept at 300mm-400mm, and the pole ought to be tilted in reverse. .
2. Do not raise the fork too high when driving. When entering and leaving the work site or while driving, be careful that there will certainly be no challenges overhead. When the tons is taking a trip, the fork needs to not be raised expensive, which will impact the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the car to shed lateral security and topple. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is forbidden to brake unexpectedly while driving with tons unless there are unique situations.
6. When the forklift is running, it must follow the website traffic rules in the factory and have to keep a certain security distance from the lorry ahead. .
7. When the forklift is running, the tons has to be in the lowest setting that does not prevent the driving, and the gantry ought to be appropriately slanted back. The tons will not be increased except when stacking or packing. .
8. The height of the tons should not block the driver's view. In unique conditions, when the thing affects the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to switch on the ramp, neither to drive throughout the ramp. .
10. The secure driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a low speed when getting in Stand-on Electric Pallet Stacker the production workshop location. .
11. When the forklift is lifted, raised or driven, it is restricted for employees to base on the fork to hold products and play a balancing role. .
12. If troubles are discovered, they will certainly be fixed and reported in a timely fashion, and they will certainly never run with ailments or hide them.
loading and unloading.
1. When fork-loading items, the distance between both forks should be changed as needed to make the lots of the two forks balanced and not skewed, and one side of the item need to protest the shelf. .
2. It is restricted to deal with a solitary fork or make use of a fork top or pull. In special conditions, safety indication should be set up to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift has to be braked with the brake. .
4. The rate of the car need to be slow-moving and steady. Be careful not to roll the wheels on the dunnage, so as not to stretch the rolled objects and hurt people. .
5. When using a fork to fork the goods, the fork ought to be as deep as possible under the lots, and it must be noted that the fork suggestion should not touch various other goods or things. The load ought to be maintained with very little back tilt of the gantry so that the load does not slide in reverse. The pole can be tilted ahead a little when the lots is reduced to enable easy positioning of the tons and removal of the forks. .
6. It is prohibited to fork goods at broadband and ram difficult items with the fork head. .
7. When the forklift is functioning, it is prohibited for people to loaf the fork, so as to avoid the collapse of the goods and injure people. .
8. Overloading is prohibited, and it is banned to make use of forks to lift personnel to participate in high-altitude procedures to prevent high-altitude falling mishaps. .
9. It is not allowed to make use of the brake inertia to slip, put, round or roll objects. .
10. It is not permitted to use forks to choose, turn pallet unload.
Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should discharge the goods or reduced the fork frame.
2. Draw the emergency brake handle to dead or depress the emergency brake button.
3. The engine is turned off and the power is removed. (Except for special circumstances, such as the chauffeur does not leave the car's line of vision and does not exceed 1 minute).
4. Remove the trick. .
Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be examined, and gas, lubricating oil and cooling water should be included.
2. Inspect the security performance of starting, running and braking.
3. Inspect whether the lights and horn signals are complete and efficient.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are typical.
5. After the forklift is running, the exterior leakage ought to also be inspected and the seals must be replaced in time.
Forklift Safety Operation Specifications.
1. You have to inspect before leaving the automobile;.
2. When you run into somebody in front of you during driving, you ought to send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be too sharp to avoid the tendency of " complimentary turning";.
6. Adding and down the slope needs to be slow-moving and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile ought to be driven backwards when declining;.
8. When the forklift personnel lug the goods and progress, if they come across large or hefty products and most likely to the motorist's line of sight, they Stand-on Electric Pallet Stacker must take the reversing exercise
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork operation is not enabled.
2. It is not permitted to raise the goods for far away driving.
3. It is not permitted to grab the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other harmful chemicals with forks.
5. It is not allowed to utilize inertia force to grab the goods.
6. It is not permitted to utilize braking pressure to exile round or easy-to-roll things.
7. It is not allowed to bring people to work with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Car park is not permitted under the following problems.
1. Contours, slim roads, train crossings;.
2. Areas with a longitudinal incline above 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the area with the exact same length as the challenge should be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844